Florida Building Code Grease Trap Sizing

09-3 as amended FAC. Pursuant to Section 4552751 Florida Statutes effective October 1 2012 licensees licensed under Chapter 455 FS.

Guidance Document For Sizing And Installation Of Grease Traps And Interceptors Pdf Free Download

ICC Digital Codes is the largest provider of model codes custom codes and standards used worldwide to construct safe sustainable affordable and resilient structures.

Florida building code grease trap sizing. D Existing grease traps grease interceptors or similar devices. Grease traps shall conform to PDI. If a new tank is installed in series the resulting configuration must meet the sizing requirements for tanks-in-series in 64E-6013.

100333 Grease trap and grease interceptor not required. Of the Florida Building Code. See P7092 for 2 inch traps you get 3 DFU each or 9 total 3 for both sinks and 3 for the Dishwasher assuming it discharges through a 2 inch trap.

Use 10 gallons for restaurants with paper or baskets and no dishwasher HR Number of hours restaurant is open. The minimum volume of any grease interceptor shall be 750 gallons and the maximum volume of an individual single grease interceptor chamber shall be 1250 gallons. 2017 FBC PLUMBING - CHAPTER 10.

The vertical distance from the fixture outlet to the trap weir shall not exceed 24 inches 610 mm and the horizontal distance shall not exceed 30 inches 610 mm measured from the centerline of the fixture outlet to the centerline of the inlet of the trap. Notwithstanding the foregoing grease traps required by this chapter shall be no smaller than an 80-gallon capacity trap with a 75-gallon per minute flow rate. C Girder size and species d Attachment of joist to girder.

Instead contact the office by phone or by traditional mail. Sizing of grease interceptors shall be based on the equations of Table 100351. Buildinghouse trapsshallbeprohib-ited except where local conditions necessitate such traps.

All interceptors shall be sized to ensure that the citys sewer system is protected from excessive FOG sand and oil which may cause clogging or damage and that the user is capable of meeting all discharge requirements. Must provide the Department with an email address if they have one. The size of a grease trap or grease interceptor shall be as determined by the MRWPCA.

A grease trap is an interceptor whose rated flow is 50gpm or less and is a device located inside a facility andor under a sink designed to collect contain or remove food wastes and grease from the wastewater while allowing the balance of the liquid waste to discharge to the wastewater collection system by gravityGrease traps are typically found in commercial locations that cook large amounts of food. Understanding how to size a grease trap is an important way to keep your establishment up to code and ensure that your plumbing is running smoothly. Each interceptor shall be constructed in accordance with Rule 64E-6 Florida Administrative Code.

GS Gallons of waste per seat use 25 gallons for restaurants with china dishes andor automatic dishwasher. A grease interceptor intended to serve as a fixture trap in accordance with the manufacturers installation instructions shall be permitted to serve as the trap for a single fixture or a combination sink of not more than three compartments where the vertical distance from the fixture outlet to the inlet of the interceptor does not exceed 30 inches 762 mm and the developed length of the waste pipe from the most upstream fixture. The minimum grease trap size gpm is the total calculated flow rate step 4 discharging.

All devices grease oil and sand interceptorstraps shall be properly sized and installed in accordance with any and all applicable requirements of County Construction Ordinance No. Each plumbing fixture shall be separately trapped by a liquid-seal trap except as otherwise permitted by this code. A grease trap or grease interceptor shall not be required for individual dwelling units or any private living quarters.

4 PLUMBING NA Plans Examiner. Shall be permitted to discharge directly into the buildings drainage system. Minimum depth of the liquid shall be 42 inches 1067 mm.

If you have any questions please contact 8504871395. The minimum tank volume of grease interceptors shall be 750 gallons 2839 L and the maximum volume of an individual grease interceptor chamber shall be 1250 gallons 4731 L. Interceptors shall be based on chapter 10 of the Florida Building Code as amended.

D Sizing of grease interceptors shall be based on the equations below. Grease interceptor or trap shall be sized and rated for the discharge of the food waste grinder. GRU - Grease trap shall be approved by Gainesville Regional Utilities.

Each compartment shall be accessible with a minimum clearance of 18 inches 457 mm square or in diameter. Signed and sealed by FL Registered Engineer. Sizing Formula for Restaurants.

B Floor joist size species and spacing. 3 Revised Mar 2018. Interceptors shall be permitted to be installed in series or as multi-chambered tanks.

64-E as amended and the State Building Code. 3 inch drain is fine The flow used for grease trap sizing is different than for drainpipe sizing. For the purposes of sizing and installation of grease interceptors all food service establishments existing within the County prior to.

How Grease Traps Work A restaurant grease trap is often specified for a pot washing stainless steel sink or a dish machine. Building traps shall be provided with a cleanout and a relief vent or fresh air intake on the inlet side of the trap. Existing tanks are not within one tank size of the required specifications found in Table II for the proposed structure they shall be replaced or supplemented to meet current sizing requirements.

100353 Inlet and outlet piping. Size type and location of grease trapsgrease interceptors shall be in accordance with. The size of the relief vent or fresh air intake shall not be less than one-half the diameter of the drain to which the relief vent or air intake connects.

Required to install operate and maintain a grease interceptor or grease trap according to the requirements of the Florida Building Code.

Gravity Grease Interceptor Design National Precast Concrete Association

2004 Florida Building Code Plumbing Fuel Gas Version

Guidance Document For Sizing And Installation Of Grease Traps And Interceptors Pdf Free Download

Guidance Document For Sizing And Installation Of Grease Traps And Interceptors Pdf Free Download

2004 Florida Building Code Plumbing Fuel Gas Version

2004 Florida Building Code Plumbing Fuel Gas Version

Grease Interceptors Grease Traps Grease Trap Types Specifications Sources Installation

2004 Florida Building Code Plumbing Fuel Gas Version

Http Www Floridabuilding Org Fbc Committees Education Technical Course Bldg Fire Fbc Plumbing Fuel Gas 4 Hr Participant Guide Pdf

Difference Between Grease Traps And Grease Interceptors Mahoney Environmental

Gravity Grease Interceptor Design National Precast Concrete Association

Http Www Floridabuilding Org Fbc Thecode 2020 Code Development March2019tacs Details Plumbing Detail V2 Pdf

Http Ecodes Biz Ecodes Support Free Resources Florida2001 Fl Plumbing Pdfs Chapter 2010 Traps Interceptors 20and 20separators Pdf

Http Scap1 Org Collection 20reference 20library Folder 20contains 20documents 20on 20fats 20oils 20and 20grease 20 Fog Tennessee 20guidance 20doc Pdf

Http Ecodes Biz Ecodes Support Free Resources Florida2001 Fl Plumbing Pdfs Chapter 2010 Traps Interceptors 20and 20separators Pdf

Gravity Grease Interceptor Design National Precast Concrete Association

Https Www Miamidade Gov Environment Library Guidelines Grease Trap Permit Pdf